STM32_TFT_8bit

8bit TFT Library for Arduino_STM32(MAPLE Core)

I ported from here.
https://github.com/prenticedavid/MCUFRIEND_kbv

Software requirement

• Core library
  https://github.com/rogerclarkmelbourne/Arduino_STM32

• Adafruit GFX Library
  https://github.com/adafruit/Adafruit-GFX-Library

Wirering for 8bit Parallel TFT

Using GPIOA as Data Port
#define TFT_DATA GPIOA

Using GPIOC as Data Port
#define TFT_DATA GPIOC

(*1)When a regulator(It's often AMS1117) is mounted on the back, it's operated 5V.
When a regulator is NOT mounted on the back, it's operated 3.3V.

(*2)By several boards, This port is used as JTAG.
You need remap.
afio_cfg_debug_ports(AFIO_DEBUG_NONE)

Pin define is "STM32_TFT_8bit.h"

Tested TFT

ILI9325 2.4inch 240x320
ILI9341 2.4inch 240x320
ILI9342 2.4inch 240x320
SPFD5408 2.4inch 240x320
R61505 2.4inch 240x320
ST7783 2.4inch 240x320
LGDP4532 2.4inch 240x320
R61509V 3.6inch 240x400
ST7793 3.6inch 240x400
ILI9481 3.5inch 320x480
ILI9486 3.5inch 320x480
RM68140 3.95inch 320x480
ST7796 3.95inch 320x480

Setting your TFT's resolution

If your TFT's resolution is 320x480,
you have to set your TFT's resolution using tft.setResoution.

Example:

ID = tft.readID();
tft.setResolution(320, 480); // Set your resolution
Serial.print("Device ID: 0x"); Serial.println(ID, HEX);
tft.begin(ID);
uint32_t width = tft.width();
Serial.print("Width: "); Serial.println(width); // You will see 320
uint32_t height = tft.height();
Serial.print("Height: "); Serial.println(height); // You will see 480

If your TFT's resolution is 240x400,
you have to set your TFT's resolution and TFT's offset.

Example:

ID = tft.readID();
tft.setResolution(240, 400); // Set your resolution
tft.setOffset(32); // Set your offset
Serial.print("Device ID: 0x"); Serial.println(ID, HEX);
tft.begin(ID);
uint32_t width = tft.width();
Serial.print("Width: "); Serial.println(width); // You will see 240
uint32_t height = tft.height();
Serial.print("Height: "); Serial.println(height); // You will see 400

• SPFD5408 + ILI9486
  

• ILI9325 + ILI9481
  

• ILI9341 + ST7793
  

• ILI9342 + R61509V
  

• ST7783 + ST7796

F4 board support

If you want more faster, plase use this.
F4 board is very fast.

JPEG Viewer

Viewer of a JPEG file in the SD card.

Software requirement

• Arduino FAT16/FAT32 Library
  https://github.com/greiman/SdFat

• JPEG decoder library
  https://github.com/Bodmer/JPEGDecoder

Wirering for TFT built-in SD-CARD Reader

*When a regulator(It's often AMS1117) is mounted on the back, it's operated 5V.
*When a regulator is NOT mounted on the back, it's operated 3.3V.

How to use

Copy JPEGS file to your SD-CARD.
*The biggest length of the JPEG file name is 32 character.
Wire TFT built-in SD-CARD Reader to STM32.
Execute JpegView_240x320_SMT32.